CXRacing LS1 Performance Racing Headers for Subaru BRZ/ Scion FRS

This is For NA Headers ONLY

Application:
Chassis : 2012-2015 Scion FR-S / Subaru BRZ
Motor : GM LS1 /LSx V8

Note:

1. No Installation Instruction Is Provided. But We Show Many Installed Pictures on This item and Installation Notes. It Is Very Intuitive.

2. Due to Limited Engine and Transmission Tunnel Space, These Modifications Are Required (See Installed Pictures):

Factory Transmission Mount Panel Needs to Be Removed and Flatten.

Front Hood Latch Support Bar Needs to Be Cut and Replaced with Our New Aluminum Bar (to Clear Front Pulley Room).

Factory Heater Tubes on the Firewall Need to be Remove.

Make Sure You Understand These Modification Requirements, Do NOT Buy This Kit If You Don't Want to Do These Mods.


Product Being Sold:
Headers ONLY

This is CXRacing's Newest Products for the Application Stated Above. All Parts Are Developed from Ground Up in Our R&D Center in USA, Designed and Built for Improved Performance Gains, with Excellent Fitment and Easy Installation.

Note:

Engine/Transmission Mounts, Exhaust Y Pipe, Oil Pan Are NOT Included, We Offer Them with Other Combinations, Please Check Our Other Products.

This Is A Proprietary Design By CXRacing, Fits CXRacing's Engine/Mount Kit, If You Use Different Mount Kit, Fitment Might Be Off.


This Product was developed based on US model Left-Hand-Drive chassis. For Right-Hand-Drive, due to potential conflict with steering shaft, fitment most likely will be an issue and we don’t guarantee fitment. Modification is needed and we won’t accept return due to Right-Hand-Drive fitment issues.

Product Info and Spec:

Header:
Long Tube Equal Length Design for More Power and Torque
1.65" OD Stainless Steel Mandrel Bent Tube Runner
3" Vband Ends for Easy Adaptation of the Rest Exhaust System

Notes:

-Off Road or Track Use ONLY, NOT for Street Use.

-Due to the Complexity of Converting a Motor from NA to Turbo, Please Make Sure You Understand the Application Stated Here is the Right Parts for Your Project.

-Parts Being Sold are the Kit Being Advertised ONLY. Other Parts Shown on Pictures are for Demo Only (of Our Complete Swap Kit). Check Our Other Products

                   

Write a review

Please login or register to review

LS1 Performance Racing Header Headers For Subaru BRZ / Scion FRS

  • Brand: CXRacing
  • Product Code: HD-LS-BRZ
  • Availability: In Stock
  • $719.50


  • Emission Notes:
  • All Parts and services offered by CXRACING are for competition vehicles only. Use on State and Federal Highways may be a violation of the EPA Clean Air Act. The Clean Air Act can be found at http://www.epa.gov/air/caa/. This document contains in detail what are considered to be violations of the CAA and corresponding penalties for failure to obey and should be read in full before purchasing or installing this competition use only product. Ensuring that all emissions, noise/sound, and speed/use related laws are followed is the responsibility of the Buyer(s). Installation and use of this product indicates that this disclaimer has been read, acknowledged, and understood fully by both the Buyer(s) and Installer(s). The Buyer(s) assumes all associated risk of the purchase.

  • Federal and several state laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. CXRacing assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer’s modifications and/or use of CXRacing products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.

  • PROPOSITION 65 WARNING

  • These products may contain chemicals known to the State of California to cause birth defects or other reproductive harm. For more information visit www.P65Warnings.ca.gov.